AlarmDecoder WebApp - Revision history

10.10.2.253 at 17:10, 18 June 2021

2021-06-18T17:10:41Z

71.237.248.220: /* Configuring SSL */

2016-03-09T23:53:20Z

‎Configuring SSL

204.10.16.29: /* Configure IP Cameras */

2015-08-24T19:29:51Z

‎Configure IP Cameras

204.10.16.29: /* Diagnostics */

2015-08-24T19:22:05Z

‎Diagnostics

204.10.16.29: /* Port Forwarding */

2015-08-24T19:21:37Z

‎Port Forwarding

204.10.16.29: /* Host Settings */

2015-08-24T19:17:10Z

‎Host Settings

204.10.16.29: /* Configuring SSL */

2015-08-10T19:12:30Z

‎Configuring SSL

204.10.16.29: /* Configuring SSL */

2015-06-25T20:07:43Z

‎Configuring SSL

204.10.16.29: /* Add Users */

2015-06-24T21:55:00Z

‎Add Users

204.10.16.29: /* Configure Device */

2015-06-24T19:59:07Z

‎Configure Device

@@ Line 25: / Line 25: @@
 ==Installation==
-; The easiest way to install the WebApp is by downloading our pre-built Raspbian image [http://www.alarmdecoder.com/wiki/index.php/Raspberry_Pi here].  However, you can follow the manual installation instructions provided on our github repository [https://github.com/nutechsoftware/alarmdecoder-webapp here]
+; The easiest way to install the WebApp is by downloading our pre-built Raspbian image [https://www.alarmdecoder.com/wiki/index.php/Raspberry_Pi here].  However, you can follow the manual installation instructions provided on our github repository [https://github.com/nutechsoftware/alarmdecoder-webapp here]
 ==Initial Setup==
@@ Line 70: / Line 70: @@
 ; Once you have told the WebApp what kind of device you have and where it is, you will be presented with a page to configure the AlarmDecoder device itself
 [[File:06_alarmdecoder_settings.png|800px|border|AlarmDecoder Device Settings]]
-; Make sure to set your address correctly!  31 for SE Panels, and for 20P Panels you will have to program an address spot into your panel and assign the AlarmDecoder the newly enabled address.  See [[http://www.alarmdecoder.com/wiki/index.php/Panel_Configuration Panel Configuration]]
+; Make sure to set your address correctly!  31 for SE Panels, and for 20P Panels you will have to program an address spot into your panel and assign the AlarmDecoder the newly enabled address.  See [[https://www.alarmdecoder.com/wiki/index.php/Panel_Configuration Panel Configuration]]

@@ Line 231: / Line 231: @@
 ;First you must create your SSL certificates and put them in the correct location
 <code>
-sudo openssl req -x509 -nodes -days 365 -newkey rsa:2048 -keyout /etc/nginx/ssl/alarmdecoder.key -out /etc/nginx/ssl/alarmdecoder.crt
+sudo openssl req -x509 -nodes -sha256 -days 365 -newkey rsa:2048 -keyout /etc/nginx/ssl/alarmdecoder.key -out /etc/nginx/ssl/alarmdecoder.crt
 </code>
 ;Just make sure to fill in the values correctly for your certificate when prompted.

@@ Line 174: / Line 174: @@
 * POST Type - urlencoded, JSON, or XML POST types supported
 * Custom Values - Here you are able to create your own key/value pairs to send with your notification
 ==Configure IP Cameras==

@@ Line 300: / Line 300: @@
 ; A Diagnostics Screen is provided under settings->Diagnostics
 ; This screen will allow you to test the functionality of the AlarmDecoder device as well as showing information about required modules.
-[[File:Diagnostics_screen.png|border|800px]]
+[[File:Diagnostics_screen.png|border|800px|Diagnostics Screen]]
 ==Disclaimers==
 ; All other trademarks are the property of their respective owners.

@@ Line 297: / Line 297: @@
 ;Some ISPs filter standard server ports, so sometimes you will have to choose an external port that is not filtered.  (Not 80, 25, 443).
 ;As an example, you may want to forward port 4443 on the outside network to port 443 of your Network Appliance.   You then would hit your external IP Address on port 4443 from your web browser.   https://public_ip_address:4443 which would then forward to port 443 of the network appliance - in SSL mode for security.
 ==Disclaimers==
 ; All other trademarks are the property of their respective owners.

@@ Line 200: / Line 200: @@
 [[File:Host_settings.png|800px|border|Example of Host Settings Page]]
 ; Here you are able to configure your device's hostname, networking, as well as reboot and shutdown the device.
+===Reboot Device===
 ==Add Users==

@@ Line 212: / Line 212: @@
 ==Configuring SSL==
 ;SSH into your raspberry pi
 ;First you must create your SSL certificates and put them in the correct location

@@ Line 203: / Line 203: @@
 ==Add Users==
-Coming soon..
+;Under Settings, click on Users - you will be presented with this screen:
 ==Configuring SSL==

← Older revision		Revision as of 19:59, 24 June 2015
Line 78:		Line 78:
	[[File:07_device_testing.png\|800px\|border\|Device Testing]]		[[File:07_device_testing.png\|800px\|border\|Device Testing]]
	; If any of these tests fail, please make sure your device is configured properly and installed properly.		; If any of these tests fail, please make sure your device is configured properly and installed properly.
		+	;Here is an example of a successful device test
		+	[[File:Success_device_testing.png\|800px\|border\|Device Testing Success]]