SmartThings and Vista 21P Panel with 14 Zones

General Discussion

SmartThings and Vista 21P Panel with 14 Zones

Postby andersondg » Fri Jan 04, 2019 7:56 am

Hello. I'm using the new/updated DH's and SmartApp for SmartThings with the AD2PI and a Vista 21P panel with 14 active zones. I see that you have updated the "ZoneTrackers" to 20, but are there any other modifications needed to support 14 active zones? I'm also getting the following error message in the AlarmDecoder (Service Manager) logs:

e4570135-1eca-434b-9817-b673099c5ab2 9:45:19 AM: error readySet: Could not find 'readyIndicator' device.
e4570135-1eca-434b-9817-b673099c5ab2 9:45:19 AM: debug getChildDevices(true), children=15

Thanks!
Duwayn
andersondg
newt
newt
 
Posts: 3
Joined: Thu Aug 03, 2017 7:48 am

Re: SmartThings and Vista 21P Panel with 14 Zones

Postby mathewss » Fri Jan 04, 2019 10:31 am

That does not sound good. If you do not have the "AD2 Ready" device then something went wrong.
It may be best to start from the beginning and be sure you have all the device handlers.


AlarmDecoder network appliance
AlarmDecoder virtual contact sensor
AlarmDecoder virtual smoke alarm
AlarmDecoder action button indicator
AlarmDecoder status indicator

I just updated Master and Dev to match. Not sure what branch you were on but you will likely need to refresh your graph.
mathewss
Moderator
Moderator
 
Posts: 30
Joined: Fri Dec 06, 2013 11:14 am

Re: SmartThings and Vista 21P Panel with 14 Zones

Postby andersondg » Fri Jan 04, 2019 11:37 am

Thank you. Are any mods required to the network appliance DH to accommodate 14 zones?
andersondg
newt
newt
 
Posts: 3
Joined: Thu Aug 03, 2017 7:48 am

Re: SmartThings and Vista 21P Panel with 14 Zones

Postby mathewss » Fri Jan 04, 2019 11:42 am

For the new zones to show up it will require removing and reinstalling the SmartThings App :(
mathewss
Moderator
Moderator
 
Posts: 30
Joined: Fri Dec 06, 2013 11:14 am

Re: SmartThings and Vista 21P Panel with 14 Zones

Postby mathewss » Fri Jan 04, 2019 11:43 am

Oh sorry no the Ad2 webapp wont need any changes for this.
mathewss
Moderator
Moderator
 
Posts: 30
Joined: Fri Dec 06, 2013 11:14 am

Re: SmartThings and Vista 21P Panel with 14 Zones

Postby andersondg » Fri Jan 04, 2019 12:19 pm

I refreshed all of the device handlers from the Master branch and am still getting the following error in the AlarmDecoder (Service Manager) log:

e4570135-1eca-434b-9817-b673099c5ab2 2:17:42 PM: error readySet: Could not find 'readyIndicator' device.
e4570135-1eca-434b-9817-b673099c5ab2 2:17:42 PM: debug getChildDevices(true), children=15

This seems to be happening when a motion detector is being tripped.

Thanks,
Duwayn
andersondg
newt
newt
 
Posts: 3
Joined: Thu Aug 03, 2017 7:48 am


Return to General

Who is online

Users browsing this forum: No registered users and 2 guests

cron