Older AD2USB not sending correctly?

General Discussion

Re: Older AD2USB not sending correctly?

Postby hamw » Fri Oct 16, 2020 7:07 pm

Could you take a sec and post a link to the debug software? I looked all over the site and did not see it. I have monogui running correctly and can upload firmware, if that is how it is done.

Thanks!!
hamw
newt
newt
 
Posts: 11
Joined: Sun Jun 06, 2010 4:44 pm

Re: Older AD2USB not sending correctly?

Postby hamw » Thu Nov 05, 2020 6:37 pm

Here we go. Did not see much diagnostic info come over. However, I did try resetting it a couple of times and also changed the apparent keypad from 31 to 19. I have three keypads and checked the addresses. I did not open a new address on the panel itself but figured it would not take/read if it was not already enabled as you mentioned.f

Next steps? Seems to not be able to send.


[code]Starting AlarmDecoderApp build #2.0.10.23844
11/5/2020 9:24:09 PM Trying to DNS resolve: 127.0.0.1
11/5/2020 9:24:09 PM Trying to connect to: 127.0.0.1:15005
11/5/2020 9:24:10 PM Loding modules. To remove modules use the modules tab under the about menu
11/5/2020 9:24:10 PM Example V1.0 initialized
11/5/2020 9:24:11 PM keypad V1.0 initialized ()
11/5/2020 9:24:11 PM MyStuff V1.0b initialized
11/5/2020 9:24:17 PM Waiting for communication to AlarmDecoder to open
11/5/2020 9:24:19 PM !SER2SOCK Connected
11/5/2020 9:24:19 PM Communicaiton to AlarmDecoder established
11/5/2020 9:24:19 PM Trying to make sure we are not in config mode sending \r\n A Bunch!
11/5/2020 9:24:19 PM Sending '\r\n' to check if in config mode.
11/5/2020 9:24:19 PM !SER2SOCK SERIAL_CONNECTED
11/5/2020 9:24:19 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:24:19 PM !MS> sending alert: AD2USBGUI Alert: mystuff initialized: DISARMED READY
11/5/2020 9:24:19 PM !RFX:0057342,fe
11/5/2020 9:24:19 PM !>RESET=Y
11/5/2020 9:24:19 PM Found config line clearing and wait again.
11/5/2020 9:24:19 PM Found config line clearing and wait again.
11/5/2020 9:24:19 PM Found config line clearing and wait again.
11/5/2020 9:24:19 PM Found config line clearing and wait again.
11/5/2020 9:24:19 PM Found config line clearing and wait again.
11/5/2020 9:24:19 PM Found config line clearing and wait again.
11/5/2020 9:24:19 PM Found config line clearing and wait again.
11/5/2020 9:24:19 PM Found config line clearing and wait again.
11/5/2020 9:24:19 PM Found config line clearing and wait again.
11/5/2020 9:24:19 PM !CONFIG>ADDRESS=31&CONFIGBITS=ff04&LRR=N&EXP=NNNNN&REL=NNNN&MASK=ffffffff&DEDUPLICATE=Y
11/5/2020 9:24:19 PM !RFX:0219646,fe
11/5/2020 9:24:19 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:24:22 PM The AlarmDecoder not in config mode. Continuing to initialize.
11/5/2020 9:24:23 PM Sending 'V' command to the AlarmDecoder
11/5/2020 9:24:23 PM !VER:ffffffff,V2.2a.6,TX;RX;SM;VZ;RF;ZX;RE;AU;3X;CG;DD;MF;LR;KE;MK;CB
11/5/2020 9:24:23 PM Found Version String
11/5/2020 9:24:32 PM !Sending......done
11/5/2020 9:24:32 PM Sending 'C' command to the AlarmDecoder
11/5/2020 9:24:32 PM Timeout waiting for !CONFIG> message from the AlarmDecoder
11/5/2020 9:24:32 PM Sending '\r\n' command to the AlarmDecoder
11/5/2020 9:24:32 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:24:32 PM !>
11/5/2020 9:24:32 PM !CONFIG>ADDRESS=31&CONFIGBITS=ff04&LRR=N&EXP=NNNNN&REL=NNNN&MASK=ffffffff&DEDUPLICATE=Y
11/5/2020 9:24:36 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:24:48 PM !Sending......done
11/5/2020 9:24:48 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:24:48 PM !RFX:0262364,18
11/5/2020 9:25:01 PM !Sending......done
11/5/2020 9:25:01 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:25:11 PM !Sending......done
11/5/2020 9:25:11 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:25:20 PM !RFX:0018516,04
11/5/2020 9:25:48 PM !>RESET=Y
11/5/2020 9:25:48 PM !CONFIG>ADDRESS=31&CONFIGBITS=ff04&LRR=N&EXP=NNNNN&REL=NNNN&MASK=ffffffff&DEDUPLICATE=Y
11/5/2020 9:25:55 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:27:02 PM !>ADDRESS=19&EXP=nnnnn&REL=nnnn&LRR=N&DEDUPLICATE=Y
11/5/2020 9:27:02 PM !setting ADDRESS 19
11/5/2020 9:27:02 PM !setting EXPANDER emulation NNNNN
11/5/2020 9:27:02 PM !setting RELAY emulation NNNN
11/5/2020 9:27:03 PM !setting LRR emulation OFF
11/5/2020 9:27:03 PM !>setting DEDUPLICATE ON
11/5/2020 9:27:03 PM !CONFIG>ADDRESS=19&CONFIGBITS=ff04&LRR=N&EXP=NNNNN&REL=NNNN&MASK=ffffffff&DEDUPLICATE=Y
11/5/2020 9:27:04 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:28:12 PM !>ADDRESS=19&EXP=nnnnn&REL=nnnn&LRR=N&DEDUPLICATE=Y
11/5/2020 9:28:12 PM !setting ADDRESS 19
11/5/2020 9:28:12 PM !setting EXPANDER emulation NNNNN
11/5/2020 9:28:12 PM !setting RELAY emulation NNNN
11/5/2020 9:28:12 PM !setting LRR emulation OFF
11/5/2020 9:28:13 PM !>setting DEDUPLICATE ON
11/5/2020 9:28:13 PM !CONFIG>ADDRESS=19&CONFIGBITS=ff04&LRR=N&EXP=NNNNN&REL=NNNN&MASK=ffffffff&DEDUPLICATE=Y
11/5/2020 9:28:14 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:29:07 PM !>
11/5/2020 9:29:07 PM !CONFIG>ADDRESS=19&CONFIGBITS=ff04&LRR=N&EXP=NNNNN&REL=NNNN&MASK=ffffffff&DEDUPLICATE=Y
11/5/2020 9:29:11 PM !>
11/5/2020 9:29:11 PM !CONFIG>ADDRESS=19&CONFIGBITS=ff04&LRR=N&EXP=NNNNN&REL=NNNN&MASK=ffffffff&DEDUPLICATE=Y
11/5/2020 9:29:13 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:29:14 PM !>ADDRESS=19&EXP=nnnnn&REL=nnnn&LRR=N&DEDUPLICATE=Y
11/5/2020 9:29:14 PM !setting ADDRESS 19
11/5/2020 9:29:14 PM !setting EXPANDER emulation NNNNN
11/5/2020 9:29:14 PM !setting RELAY emulation NNNN
11/5/2020 9:29:14 PM !setting LRR emulation OFF
11/5/2020 9:29:14 PM !>setting DEDUPLICATE ON
11/5/2020 9:29:14 PM !CONFIG>ADDRESS=19&CONFIGBITS=ff04&LRR=N&EXP=NNNNN&REL=NNNN&MASK=ffffffff&DEDUPLICATE=Y
11/5/2020 9:29:23 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:30:39 PM !Sending......done
11/5/2020 9:30:39 PM !RFX:0262364,9e
11/5/2020 9:30:39 PM !EX> Item List changed name: 0262364 id: 262364
11/5/2020 9:30:47 PM !Sending......done
11/5/2020 9:30:47 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:30:47 PM !RFX:0099164,9e
11/5/2020 9:31:12 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:31:42 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:33:00 PM !>Diag. Flag (48) :
11/5/2020 9:33:00 PM >48
11/5/2020 9:33:01 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:33:22 PM !Sending......done
11/5/2020 9:33:22 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:33:30 PM !Sending......done
11/5/2020 9:33:38 PM !Sending......done
11/5/2020 9:33:38 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:33:46 PM !Sending......done
11/5/2020 9:33:46 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "
11/5/2020 9:33:47 PM !RFX:0262364,7e
11/5/2020 9:33:47 PM !EX> Item List changed name: 0262364 id: 262364
11/5/2020 9:33:47 PM !RFX:0099164,7e
11/5/2020 9:33:47 PM !EX> Item List changed name: 0099164 id: 99164
11/5/2020 9:33:56 PM [0000000100000000----],008,[f70000ff1008000c08020000000000],"****DISARMED****Hit * for faults"
11/5/2020 9:34:04 PM !Sending......done
11/5/2020 9:34:04 PM [1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED**** Ready to Arm "/code]
hamw
newt
newt
 
Posts: 11
Joined: Sun Jun 06, 2010 4:44 pm

Re: Older AD2USB not sending correctly?

Postby hamw » Fri Nov 06, 2020 2:19 pm

Code: Select all
!SER2SOCK Connected
!SER2SOCK SERIAL_CONNECTED
@48
!>Diag. Flag (0) :>48
[1000000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED****  Ready to Arm  "
*
!Sending.done
[1001000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED****  Ready to Arm  "
C
!>
!CONFIG>ADDRESS=19&CONFIGBITS=ff04&LRR=N&EXP=NNNNN&REL=NNNN&MASK=ffffffff&DEDUPLICATE=Y
[1001000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED****  Ready to Arm  "
V
!VER:ffffffff,V2.2a.6,TX;RX;SM;VZ;RF;ZX;RE;AU;3X;CG;DD;MF;LR;KE;MK;CB
[1001000100000000----],008,[f70000ff1008001c08020000000000],"****DISARMED****  Ready to Arm  "


Helpful?
hamw
newt
newt
 
Posts: 11
Joined: Sun Jun 06, 2010 4:44 pm

Re: Older AD2USB not sending correctly?

Postby hamw » Sun Nov 08, 2020 10:31 am

Well, good news and we can put it to bed. There was nothing wrong with the AD2USB or the wiring or the panel. I did need to enable a keypad, and also enabled quick arm.

The issue was that I am using Indigo home automation software to control the panel. When I replaced the 20SE with the 20p, I continued with the same Indigo plugin that had worked with the 20SE. So, somehow the plugin would not recognize that it was seeing a new panel, and what must be a hard setting in the plugin's preferences was forcing address 31 or some other wonky behavior. I replaced that plugin with a fresh copy, reset it all and then voila it is now communicating and working as expected.

Thanks for the help ... maybe my experience might help someone else.

hamilton
hamw
newt
newt
 
Posts: 11
Joined: Sun Jun 06, 2010 4:44 pm

Previous

Return to General

Who is online

Users browsing this forum: No registered users and 4 guests

cron